• FKC SCREW PRESS STAINLESS STEEL MODEL SHX-1200 X 8000L MFG. 2006- Model: SHX-1200 X 8000L - S/N: H-2392- Type: Screw Press S/S. Inlet Cons. - Facts: 9% - 12%; Outlet Cons. 45% -50%. Production 80 BDST/D Estimated. Includes 2600 Fl Floccution Tank W/ Agitator. 60 HP, 1760 RPM - Serviced Annually By FKC - Located In Philadelphia, PA
• FKC TWIN SCREW PRESS MODEL FKC RST-HCW 775 X 3600L MFG. 2008- Model: RST-HCW 775 X 3600L - S/N: RST-209- Type: Twin Screw Press S/S Inlet Cons. - Facts: 1.5% Or Higher. Outlet Cons. 9%-12% Or Higher. Motor: Drum 10 HP, 1800 RPM, Screw: 5 HP, 1800 RPM - Serviced Annually By FKC - Located In Philadelphia, PA
• KROFTA 20' STAINLESS STEEL CLARIFIER W/ AIR DISSOLVING TUBE & CONTROLS- Diameter: 20 Feet- Make: DAF Krofta- Facts: W/ Air Dissolving Tube And Controls- 961 GPM- Used In Tissue Mill Operation - Located In Philadelphia, PA
• Fiberprep Size 2 Continuous Scavenger. S/S Construction, S/N SJC 170, With North American Electric 60 HP, 230/460-Volt Motor - Located In Philadelphia, PA
• Black Clawson Dilts Hydrapulper Ragger With Motor - Located In Philadelphia, PA
• Hansen Right Angle Pulper Drive, Model RVK24S BNN-8 No. 91/RD4A 159035, P. Nom. 2350 HP, Ratio: 8.0325 RPM Min. 1170/165.6, Comes With Oil Cooler - Located In Philadelphia, PA
• Sunds Type MD1 Vertical Stainless-Steel Mini Delta Screen And Manufactured 1998. Serial No 67069012. Equipped With A .020" (0.51mm) Slotted Screen Basket And Belt Driven By An Approximate 75 HP 1200 Rpm Motor - Located In Philadelphia, PA
• Sunds Defibrator Conflo JC 01 Refiner, No Motor - Located In Philadelphia, PA
• 84" (2.14M) Voith Roll Splitter. Hydraulic Operation. Capable Of 80" (1.52M) Diam. Rolls. Manufactured 1993. Rebulit In 2000 By VOITH. Automatic Operation. 40 HP Hydraulic Power Pack (no conveyor included only roll splitter)- Located In Philadelphia, PA
• Gorman Rupp Model, T3A61S-B / F Pump, C/I Casing, S/S Impeller And Rotor, 3" Suction, 3" Discharge, 2.5" Solids Handling, With 20 HP Motor. - Located In Philadelphia, PA
• M.A. Industries Smart-Mats Spare- Mfg. 2013 (Never Used) - Located In Philadelphia, PA
• 171" (4343mm) Roll Face Sulzer Escher Wyss 2-Roll Single Nip Calendar Stack MFG In 1986. The Calendar Is Equipped With A Self-Loaded Driven Bottom Roll And Driven Top Roll. 23" (584mm) Diameter Nipco Controlled Crown Roll With (6) Individual Controlled Pressure Zones Across The Roll Face. 36" (914mm) Diameter Temperature-Controlled Tri Pass Roll, Temp Range Top Roll 100- 250-Degree F. Bottom Roll 120-180-Degree F. Maximum Loading: 800 PLI. Maximum Design Speed: 3000 Fpm. Frame Design SEW Standard Nipcompact. Lodding DST Doctor Oscillating Blade System. Fixed Bow Mt. Hope Bow Roll. Top And Bottom Spare Calendar Rolls. Available Due To Plant Shut Down. All Documentation As Available - Located In Aberdeen, WA
• 196" (4978mm) Roll Face Farrell 2-Roll Calendar Stack, Bottom Roll Is 26" (660mm) Diameter. Nipco Type SL, Top Roll Is A 36" (914mm) Diameter Tri-Pass, Bearing Centers Approximately 228: (5.79m). Design Speed: 2000 Fpm, Design Load: 20-1000 PLI, With Controls, Spare Rolls. Complete Rebuild In Mid 1980's. Available Due To Plant Shut Down. - Located In Aberdeen, WA
• Appleton A300 Automatic Core Cutter, 120" Long Mandrel, 3" Diameter Core Size, 3/4" Wall Thickness, SN #: 82994 - Located In Philadelphia, PA
• 60" Coretech Core Cutter, Tooling for 3" Cores (Utilizes chuck system for other sizes), It has a maximum capacity of 63 inch trimmed ( at maximum throw you can put a 64 inch core, but if you trim both sides of the core 1/2 inch each side then 63 inch finished), Core is moved by using handwheel until target is triggered. 120v power, 90psi air requirement - Located In Philadelphia, PA
• 60" Semi-Automatic Core Cutter- 12"" O.D. Cores- Electronic Measurement Controller- Push Button Cutter - Located In Philadelphia, PA
• 1.2M Complete ANDRITZ WET LAP MACHINE With Outfeed Conveyor For Bales, Year Built 2001, Mdl # HDP1200, Headbox With Twin Wire Wedge Press, Heavy Duty Press Section, Cutter Layboy, Neilson And Heibert Heat Tunnel, Heavy Duty Bale Press, Oval Strapper, Discharge Conveyor. Completely Automated Operation, Capable Of Handling 160-200 AIR DRY STOCK TPD, Includes All Electrical Panels, Motors, Controls Piping, Pumps, Valves, And Spare Rolls/Parts As Available. Full Documentation Available. Presently Installed - Located In Nachez, MS
• Graphic Wizard Vivid Coater- Model: XDC - 530 Micro- Serial: 2511198- Maximum Coating Width: 20.75""- Coating Capacity: 9 pound bucket (Covers Approx. 5,000 Sheets)- Dimensions: 29.25"" Long, 35.35"" Wide, 34.25"" High- Electrical: 208/240 VAC 50/60 Hz, Single Phase - Located In Philadelphia, PA
• 60" CASCADES PAPER ROLL CLAMP MODEL 77F-RCS-236, Serial: PTL1281907-1, 8000 Pounds @ 30" L.C., 60" Roll Clamp Capacity, Clamp Weight: 2995 Pounds - Located In Philadelphia, PA
• 60" Paper Roll Clamp, Model: 90F-RCF-02C, Serial: PTL1386847-3R3, Weight Capacity: 9,000 LB @ 30 IN (4077 K @ 762 MM), Clamp Weight: 2,830 Pounds (1,282 KG) - Located In Philadelphia, PA
• 72" Cascades Roll Clamp, Model: 120F-33811R0, Serial: SPR1110981-2-R0, Manufactured 2010, Type: Split Frame Clamp, Class: IV., 10,000 Weight Capacity @ 36" Load Center, Clamp Weight: 3850lb, Positional Long Arm And Adjustable Short Arm. - Located In Philadelphia, PA
• 72" CASCADE PAPER ROLL CLAMP MODEL F100F-RCP-63996, MFG. 2014, Serial: 1848300-T2, Capacity: 10,000 Pounds At L.C., Weight: 3010 Pounds - Located In Philadelphia, PA
• 72" CASCADE PAPER ROLL CLAMP MODEL F100F-RCP-63996, MFG. 2014, Serial: 1848300-T1, Capacity: 10,000 Pounds At L.C., Weight: 3010 Pounds - Located In Philadelphia, PA
• 84" Cascade Roll Clamp- Model: 72G-RCP-228- Serial: PTL1078160-2- Capcacity: 20" Minimum - 84" Maximum- Class: III Mount- Weight: 2584- Pad: 14" Wide X 60" Tall (Double Diameter Radius) For Tissue- Manufactured: 2010 - Tissue Roll Clamp - Located In Philadelphia, PA
• 15,000 LB CATERPILLAR MODEL T150D FORKLIFT W/ SIDE SHIFT- Model: T150D- Serial: 5MB01174- Hours: 4,000 - Capacity: 15,000 Pounds- Propane Gas Fuel- Cushion Tires- Two Stage Mast- Side Shift- Four Way Valve (Roll Clamp Compatible) - Located In Philadelphia, PA
• 12,000 LB Hyster Roll Clamp Truck Mdl S120FTPRS- Serial: S120FTPRS- Serial Number G004V04067F- 7200 Hours - Mfg. 2006- 100" Mast Height In The Lowered Position. - 208" Max. Height. - Cascades 90F-RCP-01C Paper Clamp -Cascade Serial # 904590-T1 -Dimensions 56" X 156" X 102"- Approx. Weight 22,000 Lbs - Located In Philadelphia, PA
• 12,000 LB HYSTER ROLL CLAMP TRUCK S120FTPRS W/ 60" OD ROLL CLAMP Mfg: 2012- Model: S120FTPRS- Serial: H004V01523K- Clamp Model: 90F-RCS-21C- Clamp Serial: PTL1369816-2R3- 10,250 Hours- 3 Stage- Lowered Mast 100"- Raised Mast 208"- 5 Function Valve- With 60" Clamp - Located In Philadelphia, PA
• 12,000 LB HYSTER S120FTS W/ 60" CASCADE PAPER CLAMP MFG. 2016- Model: S120FTS- Serial: J004V02843P- Capacity: 12,000 Pounds - Hours: 8,254- Two Stage Mast - 85" Lowered Mast (Good For Container Loading / Unloading)- 111" Raised Mast - Four Way Valve- Cascade Paper Roll Clamp- 60" Diameter Capacity- Cushion Tires- Tested And Running - Located In Philadelphia, PA
• 12,000 LB. YALE MODEL GLC120VX FORKLIFT W/ 72" CASCADE ROLL CLAMP- Model: GLC120VX- Serial: N/A- Truck Capacity: 12,000 Pounds- Cushion Tires- Manufactured: 2011- Hours: 7,550- Three Stage Mast- 86" Lowered Mast (Good For Container Loading / Unloading)- 163" Raised Mast - Four Way Valve- Cascade Paper Roll Clamp- Clamp Model: 90F-RDP-116- 14" - 72" Diameter Capacity - Located In Philadelphia, PA
• 2011 12,000 LB. YALE MODEL GLC120VX W/ 72" CASCADE PAPER ROLL CLAMP- Model: GLC120VXNGSE084- Serial: E818V04183J- Capacity: 12,000 Pounds (8,400 Max Roll Weight)- Cusion Tires- Hours: 4,338- Three Stage Mast - 86" Lowered Mast (Good for Container Loading / Unloading)- 163" Raised Mast - Four Way Valve- Cascade Paper Roll Clamp- 72" Diameter Clamp- Model: 100F-RCP-331- Serial: PTL1246567-2- Tested and Running - Located In Philadelphia, PA
• Clark Forklift, 10,000 Lbs., Mdl: C500-100, S/N: 915-18-6365, Located In: Huntington Park, CA
• 9,000 LB YALE ROLL CLAMP TRUCK MODEL GLP090VX MFG. 2013 86" LOWERED MAST- Model: GLP090VX- Serial: H813V02512L- Stage: 3- 86" Lowered Height / 173" Raised Height- 4 Way Valve Function- Pneumatic Tires- Clamp Model: 33H-RCP-B005- Clamp: 60" Capacity- 6,600 Pounds At 30" L.C. - 9,700 Hours - Located In Philadelphia, PA
• 9,000 LB YALE ROLL CLAMP TRUCK MODEL GLP090VX MFG. 2013 86" LOWERED MAST- Model: GLP090VX- Serial: H813V02505L - Stage: 3- 86" Lowered Height / 173" Raised Height- 4 Way Valve Function- Pneumatic Tires - Clamp Model: 33H-RCP-B005- Clamp: 60" Capacity- 6,600 Pounds At 30" L.C. - 9,500 Hours - Located In Philadelphia, PA
• 8,000 LB. HYSTER ROLL CLAMP TRUCK W/ 60" CASCADE CLAMP MFG. 2010- Model: S80FT- Serial: G004V04846H- 60" Cascade Clamp- Model: 60G-RCP-255- Serial: PTL791746-3- 6000 Lbs. @ 30" Load Center- Raised Height Three Stage Mast: 173"- Lowered Height: 85"- 4 Way Valve - Liquid Propane Gas- Cushion Tires (Good Tire Life)- 11,724 Hours- Duramatch Transmission- Finger Tip Controls - Located In Philadelphia, PA
• 7,000 LB YALE FORKLIFT MDL. GLP070 MFG. 2015 ONLY 3,500 HOURS- Model: GLP070VXNLSE101- Serial: C875V03961N- 3 Stage- Raised Height: 211"- Lowered Height: 101"- Back Tilt 6 Degrees- 48" Forks - Located In Philadelphia, PA
• 6,000 LB. CATERPILLAR ROLL CLAMP TRUCK MODEL T60B- Model: T60B- Serial: 88W01655- 2,500 Hours - Roll Clamp: 60"- 3,900 Lbs. @ 30" L.C.- 9,230 Pounds (Total Weight) - Located In Philadelphia, PA
• 5,000 LB. MITSUBISHI FORKLIFT MODEL FGC25N W/ NEW TIRES- Model: FGC25N - Serial: AF82F02090- 5,000 Pound Capacity- New Tires- Manufactured: 2005- 15,700 Hours- 48" Forks - Located In Philadelphia, PA
• 1996 4,000 Lb United Tractor Cart, Model 2500845, Propane - Located In Philadelphia, PA
• 2012 Taylor-Dunn Industrial Cart- Model: R0-380-36- Serial: 187435- Weight: 1150 Pounds- Electric- Runs Good - New Batteries - Located In Philadelphia, PA
• Clark Pallet Jack- Model: P40C- Serial: P465-0350-5031FA- 4,000 Pound Capacity - With Battery Charger - Located In Philadelphia, PA
• Mark Industries Hydraulic Man Scissor Aerial Platform Lift 20', Mdl: CH20NEP, S/N: 25803, Located In: Huntington Park, CA
• Mark Industries Hydraulic Man Scissor Aerial Platform Lift 20', Mdl: CH20NEP, Located In: Huntington Park, CA
• 1,150 LB TAYLOR-DUNN INDUSTRIAL CART MFG. 2012- Model: R0-380-36- Weight: 1150 Pounds- Electric- Runs Good - Located In Philadelphia, PA
• BRODERSON CRANE 4 TON CAPACITY MDOEL IC35-2C- Serial 43875- 3,500 Hours- Gas Engine: Ford VSG-413- Boom Extension: 8FT- LP Gas Fuel System - Located In Philadelphia, PA
• BRODERSON CRANE 9 TON CAPACITY MODEL IC80-3F- 1,500 Hours- 4-Wheel Steer & 2-Wheel Drive- Boom Extension: 10 Feet- Dual Fuel System- Operator Guard - Located In Philadelphia, PA
• Coffing 3-Ton Cable Hoist With Leeson 3/4 HP, 3/60/230-460 Volt Motor - Located In Philadelphia, PA
• Harrington Hoist - Three Ton Capacity - Model: ER030L- Serial: ER1A-274-660958 - Located In Philadelphia, PA
• Dayton 2-Ton Hoist, 1 HP, 3/60/230-460 Volt Motor - Located In Philadelphia, PA
• Innomatic 63B Continuous Freeness Tester. - Located In Philadelphia, PA
• Nash CL1000 C/I Vacuum Pump. Rated For Approximately 1000 CFM. Belt Driven By 75 HP, 460-Volt, 1780 Rpm Motor. Both On Common Stand. - Located In Philadelphia, PA
• Nash CL2001 Cast Iron Vacuum Pump, Test No. 935163, Pos. 1. - Located In Philadelphia, PA
• Nash CL2001 Cast Iron Vacuum Pump, Test No. 935215, Pos. 1. - Located In Philadelphia, PA
• Nash CL2002 Cast Iron Vacuum Pump, Test No. 08k028112001002, Pos. 1, 640 RPM, Rebuilt By Gardner Denver Nash 2008 - Located In Philadelphia, PA
• Nash CL2000 Cast Iron Vacuum Pump - Located In Philadelphia, PA
• Fiberprep Size 2 Diablo Screen, Stainless Steel, S/N DBF118 - Located In Philadelphia, PA
• Celleco/Gauld Periflow Model 550 Pressure Screen. Basket, Rotor, Housing And All Wetted Parts Are 316 Stainless Steel. .004" Slotted Wedge Wire Basket. Rated Production: Accepts (Design) 75 ODTPD Accepts (Maximum) 100 ODTPD. 400 - 500 CSF. No Motor (Requires 150 HP). Belt Driven. New 1994/1995., Serial Number GFF.C550.174. - Located In Philadelphia, PA
• Falk Pulper Drive, Model 11GDXX, Right Angle, Gearbox Rated For 250HP, 5.706:1 Ratio, 870 RPM In. 152.5 RPM Out., Rebuilt In 1995 By CTMI. Included Installing New Bearings, Output Shaft And Output Sleeve - Located In Philadelphia, PA
• 20" Andritz R20 EMA II Refiner, S/N 1995 00270, No Motor. - Located In Philadelphia, PA
• Bauer 72" Wide Hydrasieve With .030" Stainless Steel Slotted Screen Plate And Fiberglass Body - Located In Philadelphia, PA
• Bauer 72" Wide Hydrasieve With .030" Slotted Screen Plate And Fiberglass Body. - Located In Philadelphia, PA
• IPEC 72" (1.82M) Wide Stainless Steel Hydrasieve, 0.06" Slotted Screen Plate. - Located In Philadelphia, PA
• Bird Axigurad 15 Screen Basket, .025" Holes, S/N 89157C, XC54 365 00070 - Located In Philadelphia, PA
• Black Clawson Size 83-SU Ultra-Clone 3" Low Density Cleaners. S/N 95UC83 SU0213 - Located In Philadelphia, PA
• Black Clawson UV300 Screen Basket, 0.062" Diameter Holes, 24: ID X 27" OD X 26" High - Located In Philadelphia, PA
• 2009 Atlas Copco Air Compressor, Serial Number: APF141784, Model GA315-FF (GA 315-125 AFF 460VY), Last Recorded Hours: 42,671, 128 PSIG Max Working Pressure, 279 KW Input Power / 374 Hp / 1789 Rotational Shaft Speed - Located In Philadelphia, PA
• 2600-Gallon Vertical Tank, 304 Stainless Steel, Cone Bottom, Top Mount Agitator, SEW Eurodrive Varimot Gearmotor With Mechanical Speed Variator, SEW 5HP, 1800 RPM, 3/60/480V - Last Used In Paper Pulping Operation - Located In Philadelphia, PA
• 24" W Roach Motorized Conveyor System, 240 Volts 3 Phase 30 AMP, 8 Long Straight Pieces (At 10' Long), 2 Short Straight Pieces (At 5' Long), 2 Corner Pieces - Located In Philadelphia, PA
• Lot Of Assorted Gate Valves: 3" Fabri Valve Slide Gate Valve Manual S/S, 3" Orbinox Slide Gate Valve Manual S/S, 4" Dezurik Slide Gate Valve Pneumatic S/S, 6" Dezurik Slide Gate Valve Pneumatic S/S, 7" Orbinox Slide Gate Valve Pneumatic S/S, 10" Orbinox Slide Gate Valve Pneumatic S/S - Located In Philadelphia, PA
• Herkules Initial Pinch Power Roll, 1 1/4" x 5', Mdl: UB12, S/N: 69133, Located In: Huntington Park, CA
• Webb Initial Pinch Plate Roll, 5/8" x 8', Mdl: 9L, S/N: 5175, Located In: Huntington Park, CA
• 1997 Marathon Vertical Hydraulic Baler 60" x 30" x 48", Mdl: V-6030HD 03, S/N: 93668, Located In: Huntington Park, CA
• 1971 Cincinnati Hydraulic Power Shear, 3/4" x 6', Mdl: 6006- 6G, S/N: 38063, Located In: Huntington Park, CA
• 1994 Betenbender Hydraulic Power Shear, 3/4" x 10', Mdl: 10-750, S/N: 105694, Located In: Huntington Park, CA
• 1985 Cincinnati Hydraulic CNC Power Shear, 3/8" x 10', Mdl: 3750 x 10, S/N: 44386, Located In: Huntington Park, CA
• Cincinnati Power Shear, 1/4" x 10', Mdl: 1810, S/N: 31860, Located In: Huntington Park, CA
• Amada Power Shear, 3/16" x 10', Mdl: M-3045, S/N: 30450628, Located In: Huntington Park, CA
• Cincinnati Power Shear, 10 Ga. x 6', Mdl: 1006-R, S/N: 35990, Located In: Huntington Park, CA
• Wysong Power Shear 10 Ga. x 6', Mdl: 1072, S/N: P4-258, Located In: Huntington Park, CA
• Hanchett Traveling Wheel Knife Grinder, 212", Mdl: AK-212C, S/N: AK316, Located In: Painesville, OH
• Hanchett Traveling Wheel Knife Grinder, 150", Mdl: AK-150, S/N: AK217, Located In: Huntington Park, CA
• 2001 6" x 122" Reform Automatic Heavy-Duty Knife Grinder, Mdl: AR 31 Type 51, S/N: 7051, Located In: Huntington Park, CA
• 2002 Reform Twin Table CNC Knife Grinder 15" x 98" Each Table, Mdl: AR70 Type 8CNC, S/N: 7077, Located In: Painesville, OH
• 1981 Landis High Precision Universal Cylindrical Grinder, 30" x 96", Mdl: 3-RH, S/N: 867-09, Located In: Painesville, OH
• Landis Plain Cylindrical Grinder, 24" x 72", Mdl: 24X72, S/N: 526-6, Located In: Huntington Park, CA
• 20" x 120" Norton Cylindrical Grinder, Mdl: 15X120, S/N: 16909, Located In: Painesville, OH
• 20" x 96" Norton Cylindrical Grinder, Mdl: 15X96, S/N: C17845, Located In: Painesville, OH
• 18" x 144" Cincinnati Cylindrical Grinder, Mdl: 16X144, S/N: 1P5K1H-1, Located In: Painesville, OH
• 17" x 144"Cincinnati Cylindrical Grinder, Mdl: 14X144, S/N: 68A22, Located In: Painesville, OH
• Landis Cylindrical Grinder, 10" x 120", Mdl: CH Plain, S/N: 510-34, Located In: Painesville, OH
• 1995 General Kinematics Vibrating Parts Shakeout, 1/8"- 1", Mdl: 1/8-1, Located In: Huntington Park, CA
• Hotsy Front Loading Heated Parts Washer 58" x 48", Mdl: APW 7953-SS, S/N: C0605-61112, Located In: Huntington Park, CA
• 1999 Hanson Heated Rotary Table Parts Washer 54" x 60", Mdl: DT-54X60-E-2000, S/N: 99-NM1167-P, Located In: Huntington Park, CA
• 1984 Pines Horizontal Hydraulic Tube Bender, 1 1/2" x 0.093" WT, Mdl: 3/4, S/N: 11000-84173, Located In: Huntington Park, CA
• 1991 Pines Vertical Hydraulic Tube Bender, 1 1/4" x 0.083" WT, Mdl: 3T, S/N: 44361-91096, Located In: Huntington Park, CA
• William Pipe & Bolt Threading Machine, 6", Mdl: HP, S/N: 5-5723-27, Located In: Painesville, OH
• Hill Acme Lead Screw Threading Machine, 1/2"- 2 1/2", Mdl: M17106, S/N: DPC-31-1776, Located In: Huntington Park, CA
• 1997 HEM Horizontal Bandsaw, 18" x 20", Mdl: F130HA-DC CCT, S/N: 582897, Located In: Huntington Park, CA
• 1996 HEM Semi-Automatic Horizontal Bandsaw, 18" x 20", Mdl: H130 HM- DC, S/N: 524196, Located In: Huntington Park, CA
• Powermatic Vertical Bandsaw, 20", Mdl: 87, S/N: 9887030, Located In: Huntington Park, CA
• 1988 Behringer Automatic Horizontal Band Saw, 11.8" x 10.2", Mdl: HBP260A, S/N: 288604, Located In: Huntington Park, CA
• 1996 Peerless Hacksaw, 10.25" x 9.75", Mdl: LHM-280, S/N: P28401, Located In: Huntington Park, CA
• Kalamazoo Vertical Tilt Frame Bandsaw, 21", Mdl: VTH-21S, S/N: 82-71-8, Located In: Huntington Park, CA
• Leblond Dual Carriage Heavy Duty Engine Lathe 52" x 58', Mdl: NR50X58, S/N: NR33, Located In: Pomona, CA
• 1980 Poreba Oil Field 12" Hollow Spindle Engine Lathe, 36" x 120", Mdl: TPL-90/3M, S/N: 0080-1197-021, Located In: Huntington Park, CA
• TOS Engine Lathe, 35" x 21', Mdl: SU-90A, S/N: 423124, Located In: Holland, OH
• Leblond Engine Lathe, 31" x 240", Mdl: 31X243, S/N: NI-814, Located In: Huntington Park, CA
• Geminis Engine Lathe, 27"/36" x 240" (20'), Mdl: GE-650, S/N: 4977, Located In: Huntington Park, CA
• Morando Engine Lathe, 24"/31" x 120", Mdl: PA-24, S/N: 45658419, Located In: Huntington Park, CA
• 1991 Turnmaster Engine Lathe, 21"/29" x 70", Mdl: 21 S, S/N: 1991193, Located In: Huntington Park, CA
• Leblond Engine Lathe, 19" x 240" (20'), Mdl: 19" E, S/N: 2E1155, Located In: Holland, OH
• Sidney Engine Lathe, 16.5" x 150", Mdl: 169-Model 16, S/N: 10237, Located In: Huntington Park, CA
• Cincinnati Vercipower Vertical Mill, 25" x 94", Mdl: 550-20, S/N: 9J53V5T-2-R-85, Located In: Huntington Park, CA
• Kearney & Trecker Vertical Mill 14" x 68", Mdl: 310TF, S/N: 7-8153, Located In: Huntington Park, CA
• Cincinnati Vercipower Horizontal Mill With Power Independent Vertical Head, 20" x 86", Mdl: 425-20, S/N: 31104CH73-0003, Located In: Huntington Park, CA
• 1966 Wotan Table Type Horizontal Boring Mill (Rotary Table), 4", Mdl: B-100S, S/N: 52386, Located In: Huntington Park, CA

In Conjunction With Maynards Industries

* All Items Subject to Seller's Acceptance of Online Bids *

BUYER'S PREMIUM

ONLINE: 18%

• Removal dates: TBA
• Removal times 8:00 AM - 4:00 PM Monday through Friday.
• No items released until payment is received in full.

Please note: BidItUp is not affiliated with any machinery rigging, transport or export company. The names and contact information of available companies are provided solely as a courtesy to our buyers. BidItUp does not endorse or guarantee the services of any machinery rigging, transport or export company, and cannot be held responsible for any damage or other problems incurred as a result of the actions of those companies. We encourage buyers to employ the service provider of their choice, provided they can supply BidItUp with the required forms and insurance certificates.